Edit 1 – 22.8. Fuel line adapter and hose made
Critical things missing – copied from earlier post
- Cam followers (1SZ-FE solids. Currently measuring clearances)
- Wiring loom (the stock wiring of the maxxecu is very long – not sure if anything serious needs to be done)
- Intercooler (Ordered a custom A2W from Plazmaman)
- Oil filter relocation hoses and misc bits
- Oil filter relocation take off plate
- Oil filter relocation other end
- TPS sensor (Possibly toyota stock)
- TPS sensor connector (Whatever toyota stock uses)
- Radium fuel pressure damper (E85 compatible)
- Radium fuel pressure regulator (E85 compatible)
- Fuel pressure gauge (Radium?)
- Adapter for Pivot fuel pressure dash gauge
- Fuel system hoses, ethanol compatible (DIY, professionally crimped?)
- Fuel system bits and misc
- Turbo oil line and drain
- Turbo coolant line and drain
Non-critical things missing
- CAN Bus wires for the ecu (found something interesting for this)
- New plugs (maybe, I got iridiums both on my current and spare engine)
- Clutch plate (maybe, no idea about the current condition)
- Fuel system (hoses, etc.) ethanol compatible
- Cam gears (maybe later and maybe toda. HKS Camshafts work with stock ones)
- Rear motor mount + damping?
- Shift lever bushing? (what was this?)
- Titanium axle bolts 🙂
- Silicone coolant hose kit
- Engine bay coolant bleeder screw
- Flex fuel sensor (when the time comes)
- Hydraulic throwout bearing (MRP)
Stuff that needs to be done
- Cleaning block (in progress)
Done list
- Intake + throttle body
- Plan A – custom intake is being made (Waiting)
- Plan B – Techno Toy Tuning adapter ordered for smallport intake (Done!)
- Trigger wheel
- Plan A – ordered from Techno Toy Tuning (Done!)
- Plan B – next door Toyota guy makes one (Waiting still but yeah)
- New pulleys (ordered from TTT, arrived, done!)
- Coatings for pistons, turbo and exhaust manifold (Done!)
- Cleaning cylinder head (Done! Found out that Aluminum boat cleaner works well (Oxalic acid))
- Injectors + connectors (Done! EV14 714cc with ethanol compability)
- Ethanol compatible fuel pump (Done! AEM)
- Cam covers (Done! But doing then better this time)
- Crank bearings (Done! Friction reducing coating)
- Conrod bearings (Done! Friction reducing coating)
- Exhaust and downpipe (Done!)
- Head gasket (Done, Cometic)
- New pistons (Done, Matrix Garage/Arias/Traum pistons)
- Gear shifter that small bearing that is at the side of the shifter (Done! Matrix Garage)
- Gear shifter bearings (Done! Matrix Garage)
- Shift base bushings (Done! Matrix Garage)
- 2-component silver paint for the epoxy painted parts (Done, tried new type of 2K paint)
- Fuel pressure regulator (Done, found the missing parts 😀 )
- Crank wheel/harmonic balancer (Done, I found a aluminium one from my stash)
- Rear tie rods (Done, Matrix Garage + installed)
- CLT sensor (Done! Bought a stock Toyota one. Thread is M12 x 1.5 – maxxecu suggest using a bosch CLT)
- New rear bearings (ordered 7.7.2018)
- Crank angle sensor bracket (D4A, 9.7.2018)
- IAT sensor
- IAT sensor connector
- CLT sensor connector
- Crank angle sensor
- Crank angle sensor connector (well, technically no)
- That special little adapter which goes to the fuel tank hardline end (working on this, ordered a stock fuel line to check this) – It’s BSP(P) 1/4″ -19
Uncertain
- Idle air valve (uncertain)
- Turbo hardware kit (uncertain)
- Aluminium radiator
- Knock sensor system (plex or that other one…)
- Engine oil cooler (laminova or something else)
Leave a Reply