Non- and critical things missing (Part 8)

Critical things missing – copied from earlier post

• Cam followers (1SZ-FE solids or Supertech CF-28/3.65)
• Wiring loom (the stock wiring of the maxxecu is very long – not sure if anything serious needs to be done)
• Oil filter relocation hoses and misc bits
• Oil filter relocation other end (I might reuse the old mocal I have)
• TPS sensor (Possibly toyota stock)
• TPS sensor connector (Whatever toyota stock uses)
• Fuel system hoses, ethanol compatible (One or two missing)
• 8mm (5/16″) fuel hard line to AN6 fitting
• Turbo oil line and drain
• Turbo coolant line and drain

Non-critical things missing

• New plugs (maybe, I got iridiums both on my current and spare engine)
• Clutch plate (maybe, no idea about the current condition)
• Cam gears (maybe later and maybe toda. HKS Camshafts work with stock ones)
• Rear motor mount + damping?
• Shift lever bushing? (what was this?)
• Titanium axle bolts 🙂
• Silicone coolant hose kit
• Engine bay coolant bleeder screw
• Flex fuel sensor (when the time comes)
• Hydraulic throwout bearing (MRP)

Stuff that needs to be done

• Cleaning block (in progress)

Done list

• Fuel system bits and misc (plenty of AN6 adapters and ORBs)
• Oil filter relocation take off plate (Canton Racing CM 22-595)
• Intercooler (custom A2W from Plazmaman)
• Adapter for Pivot fuel pressure dash gauge, decided to go for M8x1 to 1/8″ NPT adapter, this replaces the 5th injector banjo hose on fuel rail. Perfect!
• Fuel pressure gauge (Radium)
• Radium fuel pressure regulator (E85 compatible)
• Radium fuel pressure damper (E85 compatible)
• CAN Bus wires for the ecu 
• Intake + throttle body
  • Plan A – custom intake is being made (Waiting)
  • Plan B – Techno Toy Tuning adapter ordered for smallport intake (Done!)
• Trigger wheel
  • Plan A – ordered from Techno Toy Tuning (Done!)
  • Plan B – next door Toyota guy makes one (Waiting still but yeah)
• New pulleys (ordered from TTT, arrived, done!)
• Coatings for pistons, turbo and exhaust manifold (Done!)
• Cleaning cylinder head (Done! Found out that Aluminum boat cleaner works well (Oxalic acid))
• Injectors + connectors (Done! EV14 714cc with ethanol compability)
• Ethanol compatible fuel pump (Done! AEM)
• Cam covers (Done! But doing then better this time)
• Crank bearings (Done! Friction reducing coating)
• Conrod bearings (Done! Friction reducing coating)
• Exhaust and downpipe (Done!)
• Head gasket (Done, Cometic)
• New pistons (Done, Matrix Garage/Arias/Traum pistons)
• Gear shifter that small bearing that is at the side of the shifter (Done! Matrix Garage)
• Gear shifter bearings (Done! Matrix Garage)
• Shift base bushings (Done! Matrix Garage)
• 2-component silver paint for the epoxy painted parts (Done, tried new type of 2K paint)
• Fuel pressure regulator (Done, found the missing parts 😀 – actually got a new one from Radium)
• Crank wheel/harmonic balancer (Done, I found a aluminium one from my stash)
• Rear tie rods (Done, Matrix Garage + installed)
• CLT sensor (Done! Bought a stock Toyota one. Thread is M12 x 1.5 – maxxecu suggest using a bosch CLT)
• New rear bearings (ordered 7.7.2018)
• Crank angle sensor bracket (D4A, 9.7.2018)
• IAT sensor
• IAT sensor connector
• CLT sensor connector
• Crank angle sensor
• Crank angle sensor connector (well, technically no)
• That special little adapter which goes to the fuel tank hardline end (working on this, ordered a stock fuel line to check this) – It’s BSP(P) 1/4″ -19

Uncertain

• Idle air valve (uncertain)
• Turbo hardware kit (uncertain)
• Aluminium radiator
• Knock sensor system (plex or that other one…)
• Engine oil cooler (laminova or something else)