Non- and critical things missing (Part 6)

edit 1 – 3.7.2018 – added hydraulic throwout bearing

edit 2 – 4.7.2018 – added fuel pressure regulator and damper

edit 3 – 7.7.2018 – moved fuel pressure regulator and damper to critical things – realized that if I’m ever going to make ethanol compability to happen, I need to rebuild whole fuel system. Stock damper is totally out of question, it is made for a stable 2.5bar pressure and the AEM pressure regulator that I have, is not confirmed for E85. (Neither is the stock damper)

Also, made the critical things list bit more detailed if there is need to order stuff from multiple manufacturers

edit 3.1 – 7.7.2018 ordered following parts:

  • iat sensor (M12) + bung (aluminum) + connector
  • clt terminal
  • can bus wires
  • generic crank position sensor

Critical things missing – copied from earlier post

  • Cam followers (1SZ-FE solids. Currently measuring clearances)
  • Wiring loom (the stock wiring of the maxxecu is very long – not sure if anything serious needs to be done)
  • Intercooler (stock one wont do. Must order that A2W (AVT Chargecoolers?) A subaru one? A celica one?)
  • Oil filter relocation hoses and misc bits
  • Oil filter relocation take off plate
  • Oil filter relocation other end
  • IAT sensor
  • IAT sensor connector
  • CLT sensor connector
  • TPS sensor (Possibly toyota stock)
  • TPS sensor connector (Whatever toyota stock uses)
  • Crank angle sensor
  • Crank angle sensor connector
  • Crank angle sensor bracket (D4A, 9.7.2018)
  • Radium fuel pressure damper (E85 compatible)
  • Radium fuel pressure regulator (E85 compatible)
  • Fuel pressure gauge (Radium?)
  • Adapter for Pivot fuel pressure dash gauge
  • Fuel system hoses, ethanol compatible (DIY, professionally crimped?)
  • Fuel system bits and misc
  • That special little adapter which goes to the fuel tank hardline end
  • Turbo oil line and drain
  • Turbo coolant line and drain

Non-critical things missing

  • CAN Bus wires for the ecu (found something interesting for this)
  • New plugs (maybe, I got iridiums both on my current and spare engine)
  • Clutch plate (maybe, no idea about the current condition)
  • Fuel system (hoses, etc.) ethanol compatible
  • Cam gears (maybe later and maybe toda. HKS Camshafts work with stock ones)
  • Rear motor mount + damping?
  • Shift lever bushing? (what was this?)
  • Titanium axle bolts 🙂
  • Silicone coolant hose kit
  • Engine bay coolant bleeder screw
  • Flex fuel sensor (when the time comes)
  • Hydraulic throwout bearing (MRP)

Stuff that needs to be done

  • Cleaning block (in progress)

Done list

  • Intake + throttle body
    • Plan A – custom intake is being made (Waiting)
    • Plan B – Techno Toy Tuning adapter ordered for smallport intake (Done!)
  • Trigger wheel
    • Plan A – ordered from Techno Toy Tuning (Done!)
    • Plan B – next door Toyota guy makes one (Waiting still but yeah)
  • New pulleys (ordered from TTT, arrived, done!)
  • Coatings for pistons, turbo and exhaust manifold (Done!)
  • Cleaning cylinder head (Done! Found out that Aluminum boat cleaner works well (Oxalic acid))
  • Injectors + connectors (Done! EV14 714cc with ethanol compability)
  • Ethanol compatible fuel pump (Done! AEM)
  • Cam covers (Done! But doing then better this time)
  • Crank bearings (Done! Friction reducing coating)
  • Conrod bearings (Done! Friction reducing coating)
  • Exhaust and downpipe (Done!)
  • Head gasket (Done, Cometic)
  • New pistons (Done, Matrix Garage/Arias/Traum pistons)
  • Gear shifter that small bearing that is at the side of the shifter (Done! Matrix Garage)
  • Gear shifter bearings (Done! Matrix Garage)
  • Shift base bushings (Done! Matrix Garage)
  • 2-component silver paint for the epoxy painted parts (Done, tried new type of 2K paint)
  • Fuel pressure regulator (Done, found the missing parts 😀 )
  • Crank wheel/harmonic balancer (Done, I found a aluminium one from my stash)
  • Rear tie rods (Done, Matrix Garage + installed)
  • CLT sensor (Done! Bought a stock Toyota one. Thread is M12 x 1.5 – maxxecu suggest using a bosch CLT)
  • New rear bearings (ordered 7.7.2018)

Uncertain

  • Idle air valve (uncertain)
  • Turbo hardware kit (uncertain)
  • Aluminium radiator
  • Knock sensor system (plex or that other one…)
  • Engine oil cooler

Leave a Reply

avatar
  Subscribe  
Notify of