Pistons arrived! They’re Wiseco K506M815, 81.5mm (+0.5mm) oversize and with rings and other small bits.
Cat claimed the box when I presented all the stuff to her.
With the cat in the box there are ARP head studs and ARP flywheel bolts.
Tag: 4a-ge
The tide is turning!
Seems that I have reached the point where there is nothing to take apart anymore!
One of the pistons (the one that had a ultrasonic bath) taken apart and measured – maybe bit too HDR-ish photo 😀
The new oil pump, this one with 74mm gears. I found some info about how the new dry pump should be primed with grease or assembly lube, but I think that is for later.
Finally, I’ve at least primed the engine block! Got all of the paint stripped, the block cleaned and greaseless and then painted with 2-component epoxy primer (which is actually fine for only coat, but maybe light silver top coat…?)
Cleaned
Important bits taped off
Painted
Moar photos
Valve covers are off – camshafts look fairly good. MRP turbo manifold testing.
Testfitting the turbo manifold – reverse angle
There was a reason behind this pic but I’ve forgotten it
Half decent gaugepod, painted satin black and in proper place
Trying to figure out if I have stock camshafts
That 212 in the casting made me wonder – stock camshafts are 232° if I remember correctly, but then again, it could be 272 (TRD camshafts). Measuring the cam lobe finally told me that I was dealing with stock shafts. Woo-hoo.
Some engine bits in ultrasonic cleaning solution
One of the pistons looking good after washing it
Engine block going into machine shop
My turbo manifold and Beldins RS2871R GT2876R
Number one main bearing
Widric pondering if Beldins turbo would fit his Impreza
Taking spare engine apart – photos
Glorius 4AGZE!
Testfitting Manon Racing turbo manifold
Bottom
Toyota ART 8:1 pistons
Genuine (and expensive) Toyota supercharger oil
Almost bare block
(re)Building the spare engine
Ok, long story short. I went and got my spare engine out from the shed where it had been for more than two years. Took it apart and inspected everything and there was nothing serious. Block is currently getting machined to 81.5mm oversize and just got the crank back – polished and inspected (photo taken when i took the crank to the shop).
Still missing lot of parts. I’ve ordered a genuine toyota 15100-19036 oil pump, the one that I had wasnt suitable for Toda gears. Bearings needed, conrods, pistons, whatnot and a turbine 🙂
P.S. the bolt pattern upgrade isnt done yet 🙂
Removal of the oil filter relocation stuff
I built this oil filter relocation kit some time ago. For my first adventure with such things, it performed really well. There were some leaks, but relocation, pressure sensor and temperature sensor were a success.
Only thing that annoyed me was the resonance. I attached the oil filter bit next to the fuel filler hose, which got the whole fuel system resonating.
For the replacement, I just got this generic chinese made sandwich plate and decided to get rid of the whole relocation stuff.
The braided hose for the pressure sensor was perfect and i was able to mount it on top of the engine. The sensor is on the heavy side and I felt it could break free (and crack the aluminium) if left attached just to the sandwich plate. I did some heat shielding with 3M aluminium heat shield tape.
Edit: I forgot to mention, the temp sensor wiring and pressure sensor hose went between the exhaust manifold and block, otherwise i wouldn’t made the heat shielding
I had to lenghten the wires for the electric parts, which I did properly. I found very nearly the same wire with same colors and did a top notch job. The wires were soldered with supports to eliminate possible cracking in shaky enviroment.
Replacing both serpentine belts and testing a new pulley
Is it bad if the belt has a hole?
(On the left, original Toyota pulley. On the right, the one that fits BMW and now fits MR2 too)
I’m not the biggest fan of original toyota pulleys (they’re expensive and heavy) so I decided to check out if I could find an alternative. The toyota pulley is 90mm dia, around 20mm wide and has a 10mm hole.
I found a BMW tensioner pulley, which is 70mm dia, 25mm wide with 10mm hole. It is a Dayco 89046 and has a bmw part number 11 28 1 748 131. Fits at least E34 518/520/525.
Seems to work pretty well. And now it fits AW11 too.
4A oil pump plug
Finally found out what was the thread for this plug. It’s 5/8″ UNF – nice to know altough I cant use it 🙂